This MSDS Complies With 29 CFR 1910.1200 (The Hazard Communication Standard)
Section I – Product & Company Identification
Product name : CONCRETE STUCCO REMOVER
Product form: Liquid
Other means of identification: SS9113
Relevant identified uses of the substance or mixture: Cleaner
Details of the supplier of the safety data sheet
Eaton Chemical, Inc.
4124 NW Riverside Street Riverside, MO 64150
Phone: (816) 741-7985
Fax: (816) 741-0405
Emergency telephone number
Emergency number : CHEMTREC: 1-800-424-9300
Section II – Hazards Identification
CORROSIVE TO METALS – Category 1
SERIOUS EYE DAMAGE/EYE IRRITATION – Category 1
ACUTE TOXICITY – Category 4
May be corrosive to metals.
Causes severe eye damage.
Harmful if swallowed
Precautionary Statements – Prevention
Keep in original container.
Wear eye or face protection.
Wash hands thoroughly after handling. Do not eat, drink, or smoke when using this product.
Precautionary Statements – Response
Absorb spillage to prevent material damage.
IF SWALLOWED: Call a Poison Center or a doctor/physician if you feel unwell. Rinse mouth.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a Poison Center or doctor/physician.
Precautionary Statements – Storage
Store in corrosive resistant containers such as fiberglass, polyethylene, polypropylene or containers with a resistant inner liner.
Precautionary Statements – Disposal
Dispose of contents/container to an approved waste treatment and disposal facility in accordance with applicable laws and regulations, and product characteristics at time of disposal.
Section III –Composition/Information on ingredients
(CAS No) 506-89-8
Ingestion: Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention if adverse health effects persist or are severe. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Potential Effects of Exposure
Eyes: Causes serious eye damage.
Skin: Causes mild skin irritation.
Inhalation: Exposure to decomposition products may cause a health hazard. Serious effects may be delayed following exposure.
Ingestion: Harmful if swallowed. Irritating to mouth, throat and stomach.
Over Exposure Signs/Symptoms
Eye Contact: Adverse symptoms may include the following: Pain or irritation, watering, redness.
Inhalation: No known significant effects or critical hazards.
Skin Contact: Adverse symptoms may include the following: Irritation, redness.
Ingestion: Harmful if swallowed. Irritating to mouth, throat and stomach
Indication of Immediate Medical Attention and Special Treatment Needed, If Necessary
Notes to Physician: In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours.
Specific Treatments: No specific treatment
Protection of First Aiders: No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Section V – Fire Fighting Measures
Suitable Extinguishing Media
Use an extinguishing agent suitable for the surrounding fire.
Unsuitable Extinguishing Media: No data available.
Specific Hazards Arising from the Chemical
At temperatures above 60°C/140°F acid action on most metals may release hydrogen, a highly flammable and explosive gas.
Protective Equipment and Precautions for Firefighters
As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH approved and full protective gear. Keep upwind of the fire.
Section VI –Accidental Release Measures
STEPS TO BE TAKEN IN THE EVENT OF SPILLS, LEAKS, OR RELEASES
Personal Precautions, Protective Equipment and Emergency Procedures
Personal Precautions No action shall be taken involving any personal risk or without suitable training. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment.
Methods and Material for Containment and Cleaning Up
Methods for Containment: Prevent further leakage or spillage if safe to do so. Prevent discharge to the environment. Pick up and arrange for disposal without creating dust.
Methods for Cleaning Up: Use non-combustible material like vermiculite, sand or earth to soak up the product and place into a suitable container for later disposal. Do not absorb in saw-dust or other combustible absorbents.
Section VII – Handling & Storage
Precautions for Safe Handling
Advice on Safe Handling: Handle in accordance with good industrial hygiene and safety practice. Do not ingest. Avoid contact with eyes, skin and clothing. Avoid breathing vapor or mist. Wash face, hands and any exposed skin thoroughly after handling. Do not eat, drink or smoke when using this product. Use personal protection recommended in Section 8.
Conditions for Safe Storage, Including any Incompatibilities
Storage Conditions: Store only in original container. Keep containers tightly closed in a dry, cool and well-ventilated place.
Section VIII – Exposure Controls/ Personal Protection
Exposure Guidelines: None
Engineering Controls: Good general ventilation should be sufficient to control worker exposure to airborne contaminants.
Respiratory Protection: Use a properly fitted, air-purifying or supplied air respirator complying with an approved standard if a risk assessment indicates this is necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator.
Eye Protection: Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: chemical splash goggles.
Hand Protection: Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary.
Skin Protection: Prevent contact with shoes and clothing; use rubber apron and overshoes.
Other Protective Equipment: Eye wash stations and emergency showers should be available.
The type and degree of personal protective equipment appropriate will depend on the specific
work operation. Inspect and replace personal protective equipment at regular intervals; use
professional care in their selection, use and care.
Section IX – Physical & Chemical Properties
Information on Basic Physical and Chemical Properties
Physical State Liquid
Melting Point/Freezing Point No data available
Boiling Point/Boiling Range 100 o C (212 o F)
Flash Point None
Evaporation Rate No data available
Flammability (Solid,Gas) n/a-liquid
Upper Flammable Limits Not Flammable
Lower Flammable Limits Not Flammable
Vapor Pressure No data available
Vapor Density No data available
Specific Gravity 1.09
Water Solubility Soluble in Water
Solubility in Other Solvents No data available
Partition Coefficient No data available
Autoignition Temperature No data available
Decomposition Temperature No data available
Kinematic Viscosity No data available
Dynamic Viscosity No data available
Explosive Properties Not an Explosive
Oxidizing Properties No data available
Odor No data available
Odor Threshold No data available
Section X – Stability & Reactivity
Conditions to Avoid: No specific data available
Incompatible Materials: Reactive or incompatible with the following materials: oxidizing materials. This material may be extremely hazardous in contact with chlorates and nitrates. Contact with hypochlorites (eg. Chlorine bleach, sulfides or cyanides) will liberate toxic gases. Contact with alkaline materials (eg. Aqua ammonia) will generate heat.
Hazardous Decomposition Products: Under normal conditions of storage and use, hazardous decomposition products should not be produced.
Hazardous Polymerization: WILL NOT OCCUR
Section XI – Toxicological information
Information on Likely Routes of Exposure
Inhalation: Avoid breathing vapors or mists.
Eye Contact: Causes eye irritation
Skin Contact: Avoid contact with skin. Chemical Name
1120.9 mg/kg (Rat)
No data available
No data available
Section XII – Ecological information Product/ingredient name
Acute LC50 71mg/l
Acute LC0 >142mg/L
Persistence and Degradability
No data available
No data available
No data available
Section XIII – Disposal considerations
WASTE DISPOSAL METHOD
Dispose of material in accordance with all Federal, State and local regulations. Local regulations may be more stringent than Federal or State. Avoid discharge to sewers or waterways.
Section XIV – Transport information
DOT Proper Shipping Description:
Not regulated as dangerous goods.
Exempt under DOT 49 CFR 173.154 (d). This material is corrosive to aluminum only. Not corrosive to mild steel and skin
Section XV – Regulatory information
SARA Title III Section 311/312 (40CFR370): Acute health hazard
SARA Title III Section 313 (40CFR372): Not listed
CERCLA Status (40CFR302): Not listed
RCRA Status(40CFR261.33): Not listed
TSCA Inventory Status: Included
OSHA/NTP/IARC Carcinogen Status: Not listed
Canadian DSL Status: Not listed
Chemicals Known to the State of California to Cause Cancer or Reproductive Toxicity: This material is not known to contain any chemicals currently listed as carcinogens or reproductive toxins.
Section XVI – Other information
HMIS ratings: Health: 3
Indication of changes: Revision – 1
Date Sheet Prepared: 04/20/2015
Other information: Author – EHS Administrator
The information herein is presented in good faith and believed to be correct as of the date hereof. However, the manufacturer makes no representation as to the completeness and accuracy thereof. Users must make their own determination as to the suitability of the product for their purposes prior to use.
No representations or warranty’s, either express or implied of merchantability, fitness for a particular purpose or of any other nature with respect to the product or to the information herein is made hereunder. The manufacturer shall in no event be responsible for any damages of whatsoever nature directly or indirectly resulting from the publication or use of or reliance upon information contained herein.
END OF SDS